grabcad
Epoxy Gun
This is a 3d printer project. I had to use one of these for couple of days. During this...
epoxy gun 3D Models
678 resultsSponsored
grabcad
grabcad
epoxy gun
cift kompenetli epoksi tabancası altarnatif rulmana tasarlandı
thingiverse
Epoxy Gun Conversion
I had a 2:1 epoxy gun for 200 ml cartridge, but I needed an epoxy gun for a 1:1 600 ml ...
cults3d
Epoxy Gun Conversion
I had a 2:1 epoxy gun for 200 ml cartridge, but I needed an epoxy gun for a 1:1 600 ml ...
thingiverse
Epoxy gun cartridge converter
I didn't want to pay another 10-15$ (or even up to 60$ if you don't buy things from Chi...
cgtrader
Dual Epoxy Gun 3D model
This model was created in Sketchup 2017 Images are rendered using Vray Model is built t...
SPONSORED
🗳️ Will Keiko Fujimori win 2026 Peruvian election?
Latin American politics on the blockchain. Trade your conviction.
thingiverse
Epoxy gun faceplates for different cartridge sizes
If you bought one of these cheap (but very useful) epoxy guns but it didn't come with t...
thingiverse
Twin-Tube epoxy/adhesive/fill adapter for standard caulk gun
This is an adapter that allows you to use a standard caulking gun to dispense twin-tube...
thingiverse
Glue gun rest
Broke/lost a hot glue gun stand that keeps the gun upright and away from the table/floo...
thingiverse
Card / Dice Game Coaster with holder
Gaming CoastersA fun little project I made with Epoxy and left over PETG filament I had...
grabcad
Air gun silencer
3D printed air gun silencer. Works quite well. Used some Epoxy 2k to seal and strengthe...
thingiverse
Epoxy mixer nozzle for loctite two part instant mix and others
This is a replacment nozzle tip for self mixing two-part 5-minute epoxy. It's like the ...
prusaprinters
Heat gun stand
A stand for a heat gun. I created this stand so that I could adjust some eyeglasses I b...
thingiverse
Umarex Strike Point 14mm CCW Barrel Thread
This is a threaded barrel tip for the Umarex Strike Point .177cal air gun. the tip of t...
thingiverse
Kingroon KP3 KP3S KP5L micro SD guide
This remix for Kingroon KP3 KP3S KP3S Pro (and S1) and KP5L is flat on back side, reduc...
grabcad
XT30E-M
I modified an XT60E-M connector into XT30E-M just for fun. Pin bullet may be inserted m...
thingiverse
3M plunger 10:1
This is a 10:1 plunger for the 3M two part epoxy applicator gun print standing up wi...
thingiverse
Action Cam "Bobber"
Make sure all the walls are waterproof (hollowed). A layer of paint or epoxy resin wil...
thingiverse
G Point Stimulator
Have fun ;-) PLA 0.15mm Layerhöhe Slicer Simplyfy 3D Infill 20% Um die Treppen zu glätt...
thingiverse
Toyota Tundra Gas Door
Toyota tundra gas door cover, print with standrad profile in cura, use clamps to hold i...
thingiverse
Benelli MP 95E 90S front weight
This is a replacement weight for the stock weight which is very light. The weight is ...
thingiverse
Breaking Bad Fridge Magnets
Paused the print after 10 layers and switched filaments. Added those flat, flexible mag...
thingiverse
Kitefoil
dear folks that´s a, "all inclusive" hydrofoiling set. a lot of mouldings, diff...
thingiverse
Ikea Skadis Shotglass Holder (40mm)
Quickly knocked up a shotglass holder using CSD_Salzburg's awesome hangar kit - ideal f...
thingiverse
Giant Magnet Pin
I had a 1.375x0.19 inch magnet left over from another project. It was stuck to the stor...
cults3d
Genshin Impact Signora Catalyst
This is a model of Signoras Catalyst from Genshin Impact. The parts can easily be print...
thingiverse
Any Cubic Mono X Vat Nut replacement
Both my Vat nuts crumbled and broke, so I designed and printed these replacement nuts. ...
thingiverse
Pistil
The Pistil utilizes what all guns have in common: an open cylindrical hole at the deadl...
thingiverse
Crystal mold for epoxy
can be printed right side up, or upside down w/support 235C nozzle 90 bed temp 40mm/s...
thingiverse
Aprilia GEN2 RSV Mirror Block Plate
Mirror blocking plate for Gen 2 Aprilia RSV Needed Parts: 2x M6x1.0 16/20mm Bolt 2...
Sponsored
Sponsored